Goulds 1GD51G8AA 1GD Submersible Grinder Pump is engineered, built and tested in the USA. Heavy duty cast iron body and powerful 2 HP motor make this pump ideal for high head and pressure sewage systems.

**Picture is stock photo - please contact customer service for assistance in selecting the correct pump and motor for your needs.**

Specifications:

HP:  2

Body Material:  Cast Iron

Solids Handling:  3" Maximum

Motor:  Single Phase, 208V

Maximum Amps:  17.5

Locked Rotor Amps:  96.0

KVA Code:  P

Full Load Efficiency:  79%

Power Cord:  14/4 STOW 20' Length

Weight:  110 lbs

Series Features:

• Single phase pumps now have built-in overload protection.
• Impeller: Silicon bronze, multi-vane semi-open, with pump-out vanes for mechanical seal protection. Balanced for smooth operation.
• Grinder Cutter System: The anti-roping design, hardened cutter is keyed to the motor shaft for positive drive. The cutter ring is specially designed to be reversed when the first side wears out thus doubling its life and reducing maintenance costs. The cutter system is designed and tested to pass items found in normal wastewater.
• Casing: Heavy duty cast iron, volute type for maximum efficiency. Use with A10-12 guide rail system for ease of installation and maintenance.
• Dual Mechanical Seals: Silicon carbide vs. silicon carbide outer seal and ceramic vs. carbon inner seal, stainless steel metal parts, BUNA-N elastomers. Upper and lower shaft seals are positioned independently and are separated by an oil-filled chamber. Optional Silicon/Tungsten Carbide outer seal available.
• Optional Seal Sensor Probe: Located in oil-filled chamber. If pumpage should begin to leak past lower seal it indicates to pump control panel a fault has occurred. Requires optional Seal Fail Circuit in the control panel.
• Fasteners and Pipe Plugs: 300 series stainless steel.
  

Applications:

Designed for high head sewage applications where a gravity system is not practical. Ideal for pressure sewage systems

Specifications:

• Pump:
  • Solids handling capabilities: 3" maximum
  • Discharge: 11 ⁄4" NPT removable flange
  • Capacities: up to 46 GPM
  • Total heads: up to 106 feet TDH
• Motor:
  • 2 HP, 3450 RPM, 60 Hz
  • Class "F" insulation
  • Rated for continuous duty fully submerged
  • Maximum Fluid Temperature: 104º F continuous duty, 140° F intermittent duty
• Single Phase:
  • 208 or 230 volt
  • Built-in, auto reset, on-winding motor overload
• Three Phase:
  • 200, 230, 460 or 575 volt
  • Class 10 ambient compensated, overload protection required in control panel.

Motors: 

• Fully submerged in oil-filled chamber. High grade turbine oil surrounds motor for more efficient heat dissipation, permanent lubrication of bearings and mechanical seal for complete protection against outside environment.
• Class F insulation
• Single Phase: 2 HP, 208 or 230 volt, 60 Hertz, 3450 RPM, 14/4 power cord. Motor has built-in overload with automatic reset. Start capacitor, run capacitor and starting relay are required and will be located in the control panel. See “Recommended Control Panels” in chart on this bulletin.
• Three Phase: 2 HP, 200, 230, 460 or 575 V, 60 Hz, 3450 RPM. 14/4 STOW. Overload protection must be provided in starter unit.
• Designed for Continuous Operation: Pump ratings are within the motor manufacturer’s recommended working limits and can be operated continuously without damage when fully submerged.
• Bearings: Upper and lower heavy duty ball bearing construction for precision positioning of parts and to carry thrust loads.
• Power (Sensor) Cables: Severe duty rated, oil and water resistant. Epoxy seal on motor end provides secondary moisture barrier in case of outer jacket damage and to prevent oil wicking. 20 foot standard with optional lengths available.
• O-ring: Assures positive sealing against contaminants and oil leakage.
• Shaft: 300 series stainless steel, keyed design, short overhang for minimum shaft deflection.
• Pump is capable of running dry without damage to mechanical components.